 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Internationally Approved Pushbuttons Series JP Distinctive Characteristics Industry's first molded pushbutton with TV rating. Designed to handle large inrush current. JPM models certified for TV-5 rating and JPL models for TV-8 rating. Prominent external insulating barriers increase insulation resistance and dielectric strength. Constructed for dust resistance with interior seal of polyphenylene sulfide (PPS) between actuator and contact area. Specially designed to break light contact welds. Snap-action contact mechanism. Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Outer case of heat resistant resin meet UL's 94V-0 flammability standard. Actual Size JPM NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Pushbuttons Series JP General Specifications Electrical Capacity (Resistive Load) Power Level: 10A @ 125/250V AC for JPM models & 16A @ 125/250V AC for JPL models Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Latchdown: Travel: 20 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 25,000 operations minimum 25,000 operations minimum JPM Single Pole 3.53N & Double Pole 6.47N JPL Single Pole 4.51N & Double Pole 9.02 N Nonshorting (break before make) Normal position - flush with barrier; latchdown position - .079" (2.0mm) below normal Pretravel .059" (1.5mm); Overtravel .071" (1.8mm); Total Travel .130" (3.3mm) Materials & Finishes Housing/Frame & Barrier: Interior Seal: Case/Base: Polyamide (UL94V-0) Polyphenylene sulfide (UL94V-0) Melamine (UL94V-0) Movable Contacts: Stationary Contacts: Terminals: Silver alloy Silver alloy Brass with silver plating Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Process Seal: -10C through +70C (+14F through +158F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Dust resistant inner seal Installation Soldering Time & Temp: Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: TV Ratings for UL & CSA: UL File No. WOYR2.E44145 C-UL File No. WOYR8.E44145 UL Recognized: C-UL Certified: R V DE VDE Approved: UL94V-0 for housing/frame, barrier, interior seal, & case/base JPM (TV-5) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A JPM (TV-5) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A JPL (TV-8) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A JPL (TV-8) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8; add "/U" after part number to request marking on case; C-UL File No. WOYR2.E44145. All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8; add "/C-UL" after part number to request marking on case; C-UL File No. WOYR8.E44145. All JPM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC; add "/V" after part number to request marking on case; VDE License No. 113494. All JPL models approved at steady state 8A, inrush 128A, resistive 16A, & motor load 8A all at 250V AC; add "/V" after part number to request marking on case; VDE License No. 097579. NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series JP H JP RATINGS M L M 2 6 B TV-5 Rated 10A @ 125/250V AC TV-8 Rated 16A @ 125/250V AC ACTUATORS B P Flat Cap w/Barrier Flange Plunger w/Flat Flange; cap not supplied w/plunger POLES 1 2 SPST DPST 6 CIRCUIT OFF ON A B C H (Alternate Action with Latchdown) CAP COLORS Black Ivory Red Gray DESCRIPTION FOR TYPICAL ORDERING EXAMPLE JPM26B-H Gray Flat Cap with Barrier Flange TV-5 Rated 10A @ 125/250V AC DPST OFF-ON Circuit IMPORTANT: Specific models & ratings for international approvals noted on General Specifications page. NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Pushbuttons RATINGS M L TV-5 Rated Power Level 10A @ 125/250V AC Series JP TV-8 Rated Power Level 16A @ 125/250V AC Note: See General Specifications page to find complete explanation of TV ratings. POLES & CIRCUIT Plunger Position Normal Pole SP Model JPM16 JPL16 JPM26 JPL26 OFF ON OPEN 1-1a Down Connected Terminals Normal Down Throw & Schematics Note: Terminal numbers are actually on the switch. 1 (COM) SPST 1 (COM) 1a 1a 2 2a DP OFF ON OPEN 1-1a 2-2a DPST ACTUATORS B Flat Cap with Barrier Flange P Plunger with Flat Flange The barrier is an integral part of the switch. This housing is black, molded polyamide matte finish material. Cap details below. The flange is an integral part of the switch. This housing is black, molded polyamide matte finish material. No cap supplied. CAP COLORS AT3021 Flat Cap for Actuator Type B with Barrier Flange Cap Material: Polyphenylene Oxide Finish: Matte (22.0) .866 (18.0) .709 The cap is flush with the barrier in normal position and .079" (2.0mm) below that in latchdown position. (6.8) .268 Cap Colors Available: The latchdown feature on this alternate action device provides visible, audible, and tactile feedback. This design gives smooth, responsive operation. A Black B Ivory C Red H Gray NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Internationally Approved Pushbuttons PANEL CUTOUT & TERMINALS JPM & JPL Solder Lug/ .187"(4.75mm) Quick Connect Terminals (28.0) 1.102 Series JP Panel Thickness Range applies to both JPM & JPL models. .039" ~ .157" (1.0mm ~ 4.0mm) (21.2) .835 This switch assembly, when used with connectors, is not CSA approved. Epoxy Seal (7.2) (4.2) .283 (1.5) R .165 .059 (0.65) R (3.2) .026 .126 (4.75) .187 Thk = (0.5) .020 TYPICAL SWITCH DIMENSIONS B Flat Cap with Barrier Flange Part No. JPM & JPL Single & Double Pole (0.8) Typ .031 (20.8) .819 (9.4) .370 (22.0) .866 (0.5) .020 (26.6) 1.047 COM 2a 1a 2 1 (31.0) 1.220 (18.0) .709 (24.0) .945 (4.5) .177 (2.5) .098 (26.0) 1.024 Latchdown Position (1.5) .059 (7.2) .283 (10.4) .409 (21.2) .835 (4.75) Typ .187 JPM26B-H Single pole model does not have terminals 2 & 2a. P Plunger with Flat Flange Part No. JPM & JPL Single & Double Pole (0.8) Typ .031 (2.0) .079 (3.3) Sq .130 (2.5) Sq .098 (1.0) .039 (2.5) .098 (18.3) .720 (20.8) .819 (1.0) .039 (22.2) .874 (9.4) .370 (26.6) 1.047 (0.5) .020 COM 2a 1a 2 1 (31.0) 1.220 (24.0) .945 (8.5) .335 (6.5) .256 (16.0) .630 (2.0) .079 (26.0) 1.024 (1.5) .059 (7.2) .283 (10.4) .409 (21.2) .835 (4.75) Typ .187 Latchdown Position JPL16P Single pole model does not have terminals 2 & 2a. 03-07 NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com |
Price & Availability of JPM16B-A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |